Design And Exploration Of Provincial Power Grid Communication

Can wind energy be used to power mobile phone base stations?

Worldwide thousands of base stations provide relaying mobile phone signals. Every off-grid base station has a diesel generator up to 4 kW to provide electricity for the electronic equipment involved. The presentation will give attention to the requirements on using windenergy as an energy source for powering mobile phone base stations.

Do wind turbines need communication infrastructure?

However, there are several aspects that make the deployment of communication infrastructure in wind turbines and across wind farms more challenging. The location of wind turbine sites immediately increases the complexity of delivering connectivity. Remote rural sites and off-shore sites mean using standard cellular connectivity is not viable.

Why should you choose a radiating cable for a wind turbine?

These radiating cables combine highly reliable communication with a maintenance-free operation and a lifespan that lasts decades. This makes it the ideal option for achieving connectivity that spans the entire height of a wind turbine or gives complete substation coverage in both on-shore and off-shore environments.

Do wind turbine sites need cellular connectivity?

The location of wind turbine sites immediately increases the complexity of delivering connectivity. Remote rural sites and off-shore sites mean using standard cellular connectivity is not viable. Instead, there needs to be investment in a private wireless solution to give the coverage needed to operate effectively.

Why do off-grid telecommunication base stations need generators?

As the incessant demand for wireless communication grows, off-grid telecommunication base station sites continue to be introduced around the globe. In rural or remote areas, where power from the grid is unavailable or unreliable, these cell sites require generator sets to provide power security as prime power or backup standby power.

Do wind turbines block wireless signals?

Additionally, the building materials used to build wind turbines, although essential to ensure longevity, typically pose a challenge to connectivity. Tubular steel for towers, concrete towers on steel supports, and metal mesh reinforcement structures are just some examples of materials that partially or completely block wireless signals.

Are data centres and telecommunication base stations energy-saving?

Data centres (DCs) and telecommunication base stations (TBSs) are energy intensive with ∼40% of the energy consumption for cooling. Here, we provide a comprehensive review on recent research on energy-saving technologies for cooling DCs and TBSs, covering free-cooling, liquid-cooling, two-phase cooling and thermal energy storage based cooling.

How to maintain the indoor temperature of a DC or TBS?

To maintain the indoor temperature of DCs or TBSs, the computer room air conditioning (CRAC) system and chilled-water system have been developed which are energy intensive (Borah et al., 2015) and contribute more carbon emissions.

Can energy-saving cooling technologies be applied to DCS & TBSS?

Energy-saving cooling technologies, as environmentally friendly and low-cost cooling solution, have been developed low-carbon, energy-efficient and achieving sustainability (Cho et al., 2017). Such cooling technologies could be applied to DCs and TBSs since their servers and racks have similar layouts.

Do natural cooling sources increase the coefficient of performance of TBS?

They also showed an increase of the annual coefficient of performance (COP) of the TBSs by 23.7% with the ESR reaching 19.2% with the full utilization of natural cooling sources (Dong et al., 2017). Fig. 8. Schematic diagram of a water-side indirect free cooling system in the bypass of the chiller (Nadjahi et al., 2018). 3.2. Liquid cooling

What is a multi-output power supply design?

Multiple output designs may also employ a complex regulation scheme which senses multiple outputs to control the feedback loop. Voice-over-Internet-Protocol (VoIP), Digital Subscriber Line (DSL), and Third-generation (3G) base stations all necessitate varying degrees of complexity in power supply design.

What types of power systems are used in communications infrastructure equipment?

Communications infrastructure equipment employs a variety of power system components. Power factor corrected (PFC) AC/DC power supplies with load sharing and redundancy (N+1) at the front-end feed dense, high efficiency DC/DC modules and point-of-load converters on the back-end.

What is a -48V back-up battery converter?

The -48V back-up battery converter is similar in construction and complexity to the single-output, high-power VoIP converter previously discussed. The power factor corrected (PFC) AC/DC produces the supply voltage for the 3G Base station's RF Power amplifier (typ. +27V) and the bus voltage for point-of-load converters.

What is a preferred power supply architecture for DSL applications?

A preferred power supply architecture for DSL applications is illustrated in Fig. 2. A push-pull converter is used to convert the 48V input voltage to +/-12V and to provide electrical isolation. Synchronous buck converters powered off of the +12V rail generate various low-voltage outputs.

Do VoIP converters need power supply circuit topologies?

VoIP converters generally require power supply circuit topologies that are performance-driven (highly efficient with minimal conducted line current), easy to use and cost-effective with a small footprint and low profile. A number of topologies can be designed to meet these requirements to some degree.

How to choose a power supply topology for a multi-output DSL converter?

Selection criteria for the power supply topology in multi-output DSL converters include requirements for performance (high efficiency and tight load and line regulation), simplicity, low cost and a small footprint with a low profile. High performance is achieved by selecting the appropriate topology and control circuit.